Drop Weight Cummerbelt™
A Brownie's Exclusive
More than just a tow belt. More than just a weight belt. The Drop Weight Cummerbelt™ (patented) is included in these hookah systems and can change the way you dive. It's instantly adjustable for waist sizes from 24 to 54 inches, so it can fit everyone in the family. It is fully padded, depth compensating and contoured to fit your waist so you won't get the "gravity twist" like common weight belts.

It has 2 pockets - each capable of holding up to 10 lbs. of lead block or shot pouches. For added safety and control, each pocket can be instantly released by either hand (even if gloved) while still retaining the belt. You can easily achieve positive buoyancy by releasing a single pouch - much safer than dropping all your weight at once. And you always stay connected to the air hose and the surface.

DWC-4-BL

Drop Weight Cummerbelt
- Replacement Pockets (pair)*

Lose a pocket? Instead of calling the dive, keep spare pockets onboard and you'll be back in the water in no time!

find out more...

Egressor™ Scuba System
All divers are taught to carry a secondary air source in case of an emergency and hookah diving is no different. We recommend that all divers carry enough air to make a safe ascent at any time.Our patented Egressor™ systems ride along in a handy sleeve in the small of your back-out of the way, yet always convenient. Not some tiny bottle that only provides a false sense of security, our systems feature a scuba pony bottle with a standard scuba valve (6 cu. ft. for the average diver or a full 13 cu. ft. for the serious explorer), our Egressor™ scuba regulator with a low-profile HP port gauge and the retension sleeve for the back of the Drop Weight Cummerbelt™.More than just a safety device, you'll find all kinds of uses for your Egressor™ system. Light and small, it can be donned in seconds - much less time and effort than donning a full set of scuba. Perfect for quick response to items dropped over-board, verifying anchor location, hull inspection, prop clearing, pool maintenance, and much more!
DWC-EGS6-WS
DWC-EGS13-WS

find out more...

If the boat can't see you...

Hit 'em with a FOUR by FOUR™!

• Small enough to carry while boating, swimming or divingCan be carried in a pocket or clipped to your Brownie’s Cummerbelt, BCD or belt loop.Inflated, measures an 4 feet long by 4 inches wide - increase your vertical reach by over 200% Insert a chemical light stick or small flashlight in the integrated sleeve
• Over 10 pounds of emergency lift capacity
  
  4x4-INFL

find out more...

Neptune II NIRA Full Face Mask by Ocean REEF
Not just for commercial diving applications! Our Neptune II mask with integrated NIRA regulator is tuned specifically for hookah applications. The regulator can be fine tuned to the most optimum breathing. Air flows through the mask to keep the lens clear. Highest quality silicone skirt ensures a perfect seal and constant comfort.

Your entire face stays clean, warm and dry. Communications kits are available for divers to speak to each other or to a surface support crew.
33360

Diver’s Weight Belt
This belt features two inch webbing with 4 Twin Trim™ weight pockets. Each pocket holds up to 4 pounds of hard or soft shot lead weight. Simply cut and seal the belt to any length for your own custom fit. Secure side release buckle closure will not open accidently, yet can can be quickly ditched without losing the whole belt. Pockets can be distributed on different spots along the belt for greater comfort, or they can be attached directly to a scuba tank (description below) for improved trim.

WTBELT-TT

Additional Pockets sold seperately.
BCK-POC

Compressor Head Rebuild Kit
General maintenance rebuild kit for direct drive compressors includes: piston sleeve, cup, screw, o-ring, gasket, four flapper valves, and two screws. Kit also includes complete rebuild kit instructions.

Note: One rebuild kit is needed for each compressor head.

BTL-DDRB1

Compressor Rebuild Kit -
with Valve Plates
Systems with serial numbers before 10239 require this kit to bring system up to current configuration. Kit includes: valve plate, gasket, o-ring, two valve restraints, four flapper valves, two screws, piston sleeve, cup, cap, and screw. Kit also includes complete rebuild kit instructions.

Note: One rebuild kit is needed for each compressor head.

BTL-DDRB2

* Read Technical Bulletin to determine which rebuild kit is necessary for your system.

CX-6A

Over Pressure Relief Valve
Vents excess compressed air from system

PR25-008